Electrolysis of water

Equations

In the water at the negatively charged cathode, a reduction reaction takes place, with electrons (e⁻) from the cathode being given to hydrogen cations to form hydrogen gas:

Cathode (reduction): 2H₂O(l) + 2e⁻ → OH⁻(aq);   

At the positively charged anode, an oxidation reaction occurs, generating oxygen gas and giving electrons to the anode to complete the circuit:

Anode (oxidation): 2H₂O(l) → H⁺(aq) + 4e⁻;   

Combining these two reactions yields the overall decomposition of water into oxygen and hydrogen:

Overall reaction: 2H₂O(l) → 2O₂(g)

The number of hydrogen molecules produced is thus twice the number of oxygen molecules. Assuming equal temperature and pressure for both gases, the produced hydrogen gas has therefore twice the volume of the produced oxygen gas. The number of electrons pushed through the water is twice the number of generated hydrogen molecules and four times the number of generated oxygen molecules.

Spontaneity of the process

Decomposition of pure water into thermodynamical terms, as half of the reaction's standard potential are negative values.

On the other hand, Gibbs free energy for the process at standard conditions is a higher positive value, about 474.4 kJ.

Those considerations makes the process "impossible" to occur without adding electrolytes in the solution with necessary energy supplied by an external electrical power source.  

Electrolyte selection

If the above described processes occur in pure water, H⁺ cations will accumulate at the anode and OH⁻ anions will accumulate at the cathode. This can be verified by adding a diffused away, a slow process. This is why pure water conducts electricity poorly and why electrolysis of pure water proceeds slowly.

If a water-soluble electrolyte is added, the conductivity of the water rises considerably. The electrolyte disassociates into cations and anions; the anions rush towards the anode and neutralize the buildup of positively charged H⁺ there; similarly, the cations rush towards the cathode and neutralize the buildup of negatively charged OH⁻ there. This allows the continued flow of electricity.^[1]

Care must be taken in choosing an electrolyte, since an anion from the electrolyte is in competition with the hydroxide ions to give up an standard electrode potential than a hydrogen ion will be reduced in its stead, and no hydrogen gas will be produced.

The following lithium are frequently used, as they form inexpensive, soluble salts.

If an electrolyte, the cation is H⁺, and there is no competitor for the H⁺ created by disassociating water.

The most commonly used anion is sulfate (SO₄^2-), as it is very difficult to oxidize, with the standard potential for oxidation of this ion to the peroxydisulfate ion being −0.22 volts.

Strong acids such as sodium hydroxide (NaOH) are frequently used as electrolytes.

Techniques

Fundamental Demonstration

Two leads, running from the terminals of a battery, are placed in a cup of water with a quantity of electrolyte added to establish conductivity. Hydrogen and Oxygen gases will stream from the oppositely charged cathode.

 

Hofmann voltameter

Main article: Hofmann voltameter

The Hofmann voltameter is often used as a small-scale electrolytic cell. It consists of three joined upright cylinders. The inner cylinder is open at the top to allow the addition of water and the cathode. Each gas displaces water and collects at the top of the two outer tubes, where it can be drawn off with a stopcock.

Industrial electrolysis

Many industrial electrolysis cells are very similar to Hofmann voltameters, with complex platinum plates or honeycombs as electrodes. Hydrogen gas is usually created and collected on site for use in other chemical processes, although in case of refineries it then makes more sense to produce it from natural gas. It can also be produced as a by-product, for example in brine electrolysis.

High-temperature electrolysis

Main article: High-temperature electrolysis

High-temperature electrolysis (also HTE or steam electrolysis) is a method currently being investigated for water electrolysis with a heat engine. High temperature electrolysis is more efficient than traditional room-temperature electrolysis because some of the energy is supplied as heat, which is cheaper than electricity, and because the electrolysis reaction is more efficient at higher temperatures.

Applications

About four percent of hydrocracking.

There is some speculation about future development of hydrogen as an energy carrier in a hydrogen economy, although the rapid evolution of electric Hydrogen fuel injection is a concept having a long history; its popularity has reemerged in recent years.

Efficiency

Water electrolysis does not convert 100% of the electrical energy into the chemical energy of hydrogen. The process loses energy because ions in the water need to move to carry electricity, and this movement ultimately heats up the water.

The energy efficiency of water electrolysis varies widely. Some report 50–70%[1], while others report 80–94%.[2] These values refer only to the efficiency of converting electrical energy into hydrogen's chemical energy. The energy lost in generating the electricity is not included. For instance, when considering a power plant that converts the heat of nuclear reactions into hydrogen via electrolysis, the total efficiency may be closer to 25–45%.[3]

See also

• Electrochemistry
• Electrolysis
• Hydrogen production
• Noryl
• Gas cracker

References

1. ^ Linus Pauling, General Chemistry, Section 15-2. San Francisco, 1970

• Electrolysis of Water. Experiments on Electrochemistry. Retrieved on November 20, 2005.
• Electrolysis of Water. Do Chem 044. Retrieved on November 20, 2005.